MXnet 1G Evolution II Decoder with Dante
AC-MXNET-1G-DANTE-DV2 provides a stream break-out point to pass Dante signals to other Dante-enabled devices, such as Dante-capable DSP Matrix amplifiers or self-powered Dante-equipped speakers. The MXnet Evolution II platform provides system designers with flexible endpoint options while simultaneously consolidating wiring paths.
Installations that systematically deploy Dante audio but segregate it to an independent network can now simplify long-haul transport cabling into single destination endpoint routes. Encoded Dante streams are ferried from AC-MXNET-1G-DANTE-EV2 encoders to any AC-MXNET-1G-DANTE-DV2 decoder endpoint, using these as break-out bridges to leapfrog encoded signals closer to additional Dante devices. For example, Dante-enabled amplifiers can be strategically located physically closer to the speaker systems that they will power, potentially overcoming Audinate’s 100-meter Category cable distance threshold for Dante while also minimizing the lengths of wire connecting passive analog speakers. Dante-equipped self-amplified speakers may also take advantage of merged centralized stream routes. Imaginative creativity will quickly turn into material and labor savings.
The AC-MXNET-1G-DANTE-DV2 retains the cool-running, energy-efficient, chip-top fan-free design characteristics of AVPro Edge’s MXNET-1G-EVO II series by incorporating Dante I/O software into the operating system chipset, which eliminates the thermal increase from the active device daughter board in previous implementations of Dante across the MXnet ecosystem. The AC-MXNET-1G-DANTE-DV2 and its companion encoder, the AC-MXNET-1G-DANTE-EV2, each securely fit into the same accessory rack holder as standard MXnet EVO II encoders and decoders.
Proprietary Motion JPEG-based CODEC– MXnet Evolution II incorporates a proprietary video algorithm that carefully optimizes compression rates per multicast packet size. Genlock is supported, syncing a video source by frame rate to Decoders comprising a video wall for a simul-sync, tear-free appearance.
Native 4K/60 fps Support–MXnet Evolution II enables 4K/60 fps 4:4:4 RGB / YCbCr, 10- and 12-bit natively or with dynamic metadata. When not lossless, the advanced encoding/decoding engineapplies a limited, ultra-light compression, composing an artifact-free image upon decoding, including Dolby Vision and HDR10+ content.
High Bitrate Multi-channel Audio Support –3D immersive audio CODECs such as Dolby Atmos and DTS:X for IMAX Enhanced are now supported.
USB and KVM Support–The AC-MXNET-1G-DANTE-DV2 features a USB 2.0 Type-B female Host connection, enabling MXnet Mentor software to configure easy routing for bi-directional USB signals from a designated Host Encoder to a downstream decoder with a connected USB device.
USB video downstream processing has been improved and now supports resolutions up to 1920x1080p@30 Hz.
External Device Light Control-Light emission from an AC-MXNET-1G-DANTE-DV2 may be controlled via MXnet Mentor. Any status light, including network link LEDs and the OLED Data Window, may be optionally disabled to prevent unwanted distraction, enabling discreet placement where desired. Device lights may also be continuously “flashed” for high visibility when troubleshooting.
In the Box
- AC-MXNET-1G-DANTE-DV2 (Decoder/Receiver Device)
- 1 x IR Emitter
- 1 x IR Receiver
- 2 x Mounting Brackets
- 4 x Screws forMounting Brackets
- 1 x 3-Pin Terminal Block
FEATURES
- Dante audio Pass-through/Break-out Bridge
- High bitrate 3D Immersive Audio Compatible
- Optimized Video Compression for Artifact-free Images
- Support for HDR10, HDR10+ and Dolby Vision
- USB and KVM Support
SPECIFICATIONS
AC-MXNET1G-DANTE-DV2 | |
Encoding | |
Video Codec | Proprietary Codec based on M-JPEG, Dante |
Audio Codec | Proprietary Codec, Dante |
Latency | 16ms@60Hz |
Streaming Protocols | TCP, UDP, IP, IGMP-V2 |
Copy Protection | HDCP 2.2 and earlier |
Video Input/Ingestion | |
Signal Type | DVI 1.0, HDMI 2.0b |
Video Resolution | 720p@50/60Hz; 1080p@24, 50 & 60Hz; 4K@50/60Hz 4:4:4*; 4K@30Hz 4:4:4; 4K@60Hz 4:2:0;4:2:2 4K@24Hz 4:2:0/4:2:2 [Ultrawide Support] |
Chroma Subsampling | 4:4:4, 4:2:2, 4:2:0, RGB |
Bit Depth per Color | 1080p 8-,10-,12-bit, 4K 8-,10-,12-bit |
Visually Lossless | 4096x2160p@60Hz (8-bit) 4:4:4 or RGB; 3840x2160p@60Hz (12-bit) 4:2:2 Dolby Vision; 3840x2160p@60Hz (10-bit) 4:2:2 HDR10/HLG; 1920x1080p@60HZ (12-bit) |
Audio | |
Audio Format (end to end) | PCM 2, 5.1, 7.1 Channel, Dolby Digital 5.1 Channel, Dolby Digital Plus, DTS 5.1 Channel, DTS–ES, DTS–HD High Resolution, DTS-HD Master Audio, Dolby Atmos |
Audio Format (HDMI Loopout) | Same As End-To-End |
Embedded Audio | Stereo Analog Audio (3.5 mm jack) |
De-Embedded Audio | Balanced Stereo Analog Audio (5-pin phoenix Only) (Audio downmixed to PCM 2Ch) |
Ports | |
Ethernet | (1) × female RJ45, PoE |
SFP | (1) × SFP Slot |
HDMI | (2) × HDMI Type A 19-pin, female, one HDMI input, one HDMI loop out |
Audio | (1) × 5-pin Terminal Block, Balanced L/R Audio out (downmixed to 2Ch) |
(1) x Toslink Audio Out (Future Audio Return Support Only) | |
(1) × 3.5 mm mini stereo jack, Audio in | |
IR | (3) × 3.5 mm mini-stereo jack, one IR-Pass, one IR-EYE, one IR-out |
RS232 | (1) × 3 Pin Terminal Block |
USB | (1) × USB 2.0 Type-B for USB extension and KVM |
(1) × USB Type-C for MXNet service | |
Distance | |
Ethernet | 100 Meters/ 330 Feet over CAT5e and above |
SFP and Fiber | 1000BASE-SX SFP Transceiver Module |
(MMF, 850nm, 550m, LC, DOM) | |
1000BASE-LX/LH SFP 1310nm 10km Transceiver Module | |
Environmental | |
Operating Temperature | 23 to 125°F (-5 to 51°C) |
Storage Temperature | -4 to 140°F (-20 to 60°C) |
Operating Humidity | 5-90% RH (No Condensation) |
Cooling | Fanless Cooling |
Acoustic Noise Level | 0dB |
Power | |
Max Power Consumption | 9.7W |
PoE (Power over Ethernet) | IEEE 802.3af (15.4W) |
Power Supply Unit | Input: AC 120-240V-50/60Hz 0.8A |
Dimensions | |
Mounting | Rack and furniture mount support |
Dimensions (Unit only Width/Depth/Height) | mm: 199.14 x 119.86 x 19.84 inch: 7.84 x 4.72 x .78 |
Dimensions(Packaged Width/Depth/Height) | mm: 309.88 x 180.09 x 54.10 inch: 12.2 x 7.09 x 2.13 |
Weight (Unit) | 1.41 lbs / .64 kg |
Weight (Packaged) | 1.87 lbs / .85 kg |
Regulatory | CE/FCC/UL |
*Specifications subject to change without notice. Mass & dimensions are approximate |
SUPPORT
Manuals and Guides
- Manual
Sales Resources
- Data Sheet
*
*
*